Unsure how to use some of the products in your Character pack or Mystery box?
Here are some basic instructions for you!
WHITE FOUNDATION PACK:
Soak makeup sponge and squeeze out ALL excess water - this makes the sponge softer. Apply white cream paint stick directly onto the skin, even out with sponge. Press the Super white powder into the FX creme with the powder puff. This will make the FX creme set and now you can apply other make-up on top of it. To Remove: Wash with soap and warm water.
Soak makeup sponge and squeeze out ALL excess water - this makes the sponge softer. Apply white cream paint stick directly onto the skin, even out with sponge. Press the Super white powder into the FX creme with the powder puff. This will make the FX creme set and now you can apply other make-up on top of it. To Remove: Wash with soap and warm water.
------------------
FACE PAINT:
Face Paint and Sponge: Moisten sponge slightly with water, squeezing any excess. Rub moist sponge onto face paint. Gently dab onto skin, creating a uniform layer. Blend edges for smooth colour transitions. Face Paint and Brush: Lightly dip your into water, and swirl brush into the face paint. Colours can be layered on top of base face paint. For removal, wash with warm water and gentle soap. Rinse, then moisturize.
------------------
SHADERS:
With a brush, apply on eyelids for a smoky eyeshadow look. For depth/gaunt makeup looks, shade the hollows of cheeks, temples, and nose sides. Blend edges seamlessly. To remove: use an eye makeup remover or micellar water, gently wiping away. Rinse and moisturize.
With a brush, apply on eyelids for a smoky eyeshadow look. For depth/gaunt makeup looks, shade the hollows of cheeks, temples, and nose sides. Blend edges seamlessly. To remove: use an eye makeup remover or micellar water, gently wiping away. Rinse and moisturize.
------------------
LATEX PROSTHETICS & PROSAIDE (HORNS, EARS, NOSES)
Clean skin. Apply thin Prosaide layer where prosthetic will sit. Apply thin Prosaide layer on to prosthetic, let dry till transparent. Position latex piece onto adhesive. Press and set. To remove: Can apply adhesive remover or 99% alcohol at edges, gently lifting.Or if possible, carefully peel away from skin. Remove residue with oil, cleanse with soap and water. Moisturize skin. Always patch-test for sensitivities.
Clean skin. Apply thin Prosaide layer where prosthetic will sit. Apply thin Prosaide layer on to prosthetic, let dry till transparent. Position latex piece onto adhesive. Press and set. To remove: Can apply adhesive remover or 99% alcohol at edges, gently lifting.Or if possible, carefully peel away from skin. Remove residue with oil, cleanse with soap and water. Moisturize skin. Always patch-test for sensitivities.
------------------
MAGIC EYELINER:
Delicately draw on the lash line. While still tacky, adhere glitter or press lashes onto the liner. It securely bonds as it dries. Powder off to reduce stickiness. To remove: use a gentle makeup remover, carefully wiping away. Rinse and moisturize.
------------------
LIQUID EYELINER:
Steadily draw close to the lash line with the applicator. Start from the inner corner, progressing outward. To remove: dab a cotton pad with eye makeup remover, softly wiping off. Rinse and hydrate.
------------------
DAUBER:
Dip dauber into water, and press it out onto a towel to remove excess moisture. Rub the dauber into paint. Press through the stencil, guaranteeing even transfer.If the dauber is too wet, the paint will seep under the stencil, and you will lose detail. Dab it out onto a towel, reload with paint and try again!
------------------
LIQUID LIPPY:
Utilizing the built-in applicator, begin at the lip center, spreading outwards for a consistent coat. Let dry for enduring wear. To remove: use oil-based makeup remover. Gently rub, then rinse.
Utilizing the built-in applicator, begin at the lip center, spreading outwards for a consistent coat. Let dry for enduring wear. To remove: use oil-based makeup remover. Gently rub, then rinse.
------------------
CONTACT LENSES:
Before handling contact lenses, wash hands thoroughly with soap and dry with a lint-free towel. Using your index finger and thumb, gently remove a lens from its case. Inspect for debris or tears. Place the lens on the tip of your index finger, ensuring it's not inside out. Pull down your lower eyelid with your middle finger, and use your other hand to hold up the upper lid. Gently place the lens on your eye. Blink a few times to position the lens. To remove: look up, pull down your lower eyelid, and gently pinch the lens between thumb and index finger, pulling it away. Store lenses in fresh solution. Never wear damaged lenses. Never share lenses. Throw 1 day lenses out after use.
------------------
COAGULATED BLOOD OR BLOOD JAM:
With fingers or a tool, apply for a denser, textured blood effect. Perfect for intense, gory appearances. Create realistic grazes with a stipple sponge. To remove, use warm water and soap, massaging gently until fully removed.
------------------
STAGE BLOOD:
Dip applicator brush into stage blood. Paint into special FX wounds for realistic effect. Blood does dry but will remain slightly sticky. Use dark blood for deeper wounds, bright blood for shallow cuts and grazes. To remove: gently cleanse with warm water and soap, using circular motions. Rinse thoroughly.
------------------
SQUIRT BLOOD:
Squeeze bottle for a realistic, flowing blood effect. Ideal for fresh wounds or active bleeding scenes. To clean off, rinse thoroughly with water, then wash with soap and water.
------------------
STENCILS:
Position stencil firmly against skin. Gently apply product over the design, ensuring even and full coverage. Carefully lift stencil, revealing your pattern. Removal depends on the product used; use appropriate makeup remover or soap and water.
Position stencil firmly against skin. Gently apply product over the design, ensuring even and full coverage. Carefully lift stencil, revealing your pattern. Removal depends on the product used; use appropriate makeup remover or soap and water.
------------------
SILICONE MOULD & GELATINE PROSTHETIC:
Heat gelatine in microwave in 10 second increments - do not boil.
Pour into silicone mould and let it cool completely.
To apply: heat some more gelatine and spread onto the skin where you want your prosthetic (check that it's not too hot first).
To apply: heat some more gelatine and spread onto the skin where you want your prosthetic (check that it's not too hot first).
Put the whole silicone mould with cooled gelatine onto the skin with gelatine, hold for 3 minutes and carefully peel away the silicone mould.
You can paint the gelatine to match your makeup and add blood if necessary. To remove: just warm water will melt away the gelatine.